Silicone rubber and metal bonding process

by:Keyuan     2020-12-04
With the constant innovation of the silicone industry technology progress, silicone rubber in the application of life is becoming more and more widely, but sometimes will run into some problems in application, how can such as silicone rubber products with metal bond, silicone rubber and metal bonding below to share with you the four step process: a, metal surface treatment, to achieve adhesion, first of all to the metal surface processing, the commonly used method is: chemical, mechanical, and three kinds of solvent, silicone products factory is chosen according to the actual method commonly, sandblasting machine processing method often USES, use sand cloth or emery wheel grinding, especially sand blasting method, low cost, fast speed, the effect is good, for a wide range of applications. Chemical treatments are commonly used, especially the anodized aluminium and its alloys, copper plating of steel processing, need to use chemical method. After processing the surface of the metal, after processing the surface of the coated with adhesive, silicone rubber or immersed in an inert solvent. Second, the metal connector ( Recommended products: fluorine rubber joint) Design, to realize the uf resin, silicone rubber and metal bonding joint second to start, because part of the overall design of the products below to understand the design principle of joint: 1) Try to increase the bonding area, improve the bearing capacity of the adhesive joint; 2) Adhesive joint stress modes should be shear or tensile force, prevent stripping force; 3) In the direction of the mechanical bonding length shoulds not be too long, should try to increase the adhesive width; 4) Lamination adhesive force direction should avoid interlayer separation; 5) Angle is better than that of rectangular component; 6) The transverse stress of joint surface adhesion should be adopted. According to the above principles and the characteristics of the rubber products, commonly used in the method such as drilling, threading groove of the metal, glue in order to improve the joint strength. Three construction qualified metal surface treatment, adhesive, the adhesive surface can be brush, spray, roll, knife, impregnation method such as falls, use what method, can according to the size of the piece and the properties of the adhesive to decide. Four, stick glue and sulfide with ReTie and cold two methods, after the viscose mechanical or available for compaction pressure series. Film shoulds not be too thick, adopt the method of step by step a thin film paste to the required thickness. General hard film thickness is 0. 1 to 1. 5 mm, soft film thickness is no more than 4 to 5 mm, in order to avoid the film contains bubbles. Vulcanization glue can be divided into hot vulcanization and cold cure. Hot vulcanization glue is a good film will be posted in a certain pressure and temperature of the metal, make the finished rubber and metal bonding. Cold vulcanized adhesive is to use adhesive at room temperature, through certain time pressure nature sulfide, vulcanized rubber and metal bonding. Compression is indispensable to bonding process conditions, pressure and temperature, depending on the products and its formula. Above all, to achieve the adhesion of silicone rubber and metal, according to the four steps, the metal surface, joint, adhesive, bonding method, but the silicone products factory in implementation should pay attention to the following points, such as metal surfaces treated by chemical method if not handled in time will be affected by dust, such as greenhouse gas pollution rust and oxidation, and construction of the binder for uniform and must be attached with glue, glue the environment temperature should be controlled in 15 ~ 35 ℃, relative humidity below 70%, the solvent volatilization completely and avoid surface dew. Popular articles relevant recommendation: silicone rubber products factory production process of vulcanization silicone rubber products production process gift silicone wrist band glue interpretation process for the production of silicone products is a complex process, so the silicone product quality in addition to the machine and human factors. Intermediate inspection is found and the key to solve the problem of major silicone product quality. Therefore, maintain the normal operation of the machine, mold good working state, strengthen the operation of the operator and qc personnel skills and quality consciousness training is the key to reduce production bad, is also the benefit of our silicone rubber products; So we sincerely invite you to contact our communication: mobile: 13392830612 phone: fax: email: address: ( Foshan rubber products manufacturers) Address: foshan city guanlan street water pits or hanging about gold and red industrial park 5 / f, building B
Custom message
Chat Online 编辑模式下无法使用
Chat Online inputting...